Gunsmithing Services

Sight Installation — installation of front and rear sights, centering on slide and Loctite screws (if applicable) with free adjustment

• Sights purchased at BWSC –  $25
• Sights provided by customer – $50
• 1911 / High Power sight install – starting at $50

Drop-In Trigger Install — $80 (plus test fire) – installation of drop-in trigger on most handgun models, polishing of trigger engagement surfaces, safety, and function test

Semi Drop-In Barrel Install — $80 – file and/or machine to correct fitment, function test and live fire test for proper function

Match Grade Gunsmith-fit Barrel Install – $100 – file and/or machine to correct fitment, function test and live fire test for proper function

Polish Feed Ramps (add-on) – $25

Stake-In Front Sight – $80 – installing stake in style 1911 front sight

Non-Ramped Barrel Install – $120 – file and/or machine barrel to correct fit and test fire for proper function

Fit Barrel Bushing – $90 – fit barrel bushing to slide and barrel

Lower and Flair Ejection Port – $100 – machine ejection port lower and flair for ejection (refinish additional)

Fit After-Market Trigger Shoe– $75 – fit aftermarket trigger to frame and polish trigger bow

Fit Thumb Safety – $50 – fit safety for proper function

Fit Beavertail Safety – $180 – fit beavertail safety to frame (Ed Brown, Wilson Combat, etc.) (refinish additional)

Fit Extended Magazine Release – $50 – fit and test magazine release for proper function

Scope Mount & Boresight — $60 – installation of scope and rings, leveling of sight plane, setting of eye relief, Loctite screws and bore sighting at simulated 100 yards… (test fire additional). Discount if mount and scope are purchased at BWSC – $30

Scope Ring Lapping – $40 – mount lap scope rings on rifle for proper fitment and alignment for scope (1″, 30mm, 34mm) – does not include scope mounting

Muzzle Device Install — $50 – installation and proper timing of muzzle device (i.e. flash hider, muzzle brake) torqued to proper specification and Rocksett if needed

Sling Swivel Install – $60 – drill and install sling swivels to stock (plus hardware)

Pour Chamber Cast — $75 – to determine condition or proper caliber or chamber specifications

Barrel Threading — starting at $150 –thread most bolt action rifles or stand-alone barrels to customer preferred thread (subject to barrel diameter). Cut to shorter length and recrown before threading +$50

Blend Muzzle Break (add-on to threading) – $60 – blend rear of muzzle device to better flow with barrel profile 

Seamless Muzzle Break – depending on finish (add-on to threading) – $200 – blend and time muzzle device to appear as part of the barrel. Refinishing additional if necessary.

Cut and Recrown Barrel – $120

Recrown Barrel at current length – $100

Glass Bedding – $120 – glass bed action to fit rifle stock

Pillar Bedding – $200 – install aluminum pillars and glass bed action to stock

Home Build Checkup — $65 – inspect firearm, measure of headspace, torque check barrel, castle nut and function check

Lower Receiver Assembly — $75 – installation of lower parts kit, filing for fit if needed

Upper Receiver Assembly — $75 – install barrel, handguard and gas system for proper torque and alignment with head space check

Complete Assembly – $140 – complete assembly of firearm with customer provided receivers and parts. Includes headspace check and two-round test fire. 

Barrel or Handguard Change — $65 – remove and install new barrel or handguard at proper torque and timing

Trigger Installation — $50 – installation and fitting of trigger followed by safety and function check

A2 Front Sight Post Removal – $75 – remove sight post material to turn an A2 post into a low-profile gas block

AR-15 Full Tune Up — $150 – detail clean, inspection and small part replacement as needed (including detent, hammer, & trigger springs, gas rings, firing pin). Stamdard parts, excluding proprietary parts

Muzzle Device Install – $50 – installation and proper timing of muzzle device, torqued to proper specification, and Rocksett if needed

Pin & Weld Muzzle Device — $80 – permanent weld attachment onto threaded barrel

Remove Pin & Weld – $80 – removal of previously pinned and welded muzzle device

Polish Feed Ramps (add-on) – $25 – blend and polish feed ramps and receiver

Bead Replacement – $15 – includes standard brass or aluminum bead

Drill & Tap Bead – $50 – drill and tap barrel for bead (includes brass or aluminum bead)

Recoil Pad Installation — $175 – determine proper length of pull for individual, grind pad to proper fit on stock (includes new Kick-EEZ or Pachmayr pad), installation

Recoil Pad Spacer – $25 – fit spacer along with a recoil pad installation to increase length of pull (requires new recoil pad)

Remington Shell Stop Staking – $50 – install and stake Remington shell stops (parts not included)

Cut Crown and Re-Bead – $120 – cut barrel to length, crown, and install a new bead

1911 Trigger Job – $160 – fit and polish all trigger parts to a 3.5-4lb pull trigger (parts not included)

10/22 Trigger Job – $75 – modify factory trigger to 4lb pull with overtravel stop (parts included)

Revolver Trigger Job – starting at $150 – polish frame and parts, installation of springs (parts included) for Smith & Wesson, Ruger, Colt

Lever Action Trigger Job – $165 – subject to model

Bolt Action Trigger Install and Tune – $65 – install trigger and adjust if applicable